Step 1
Prep glue pull tabs by soaking them in 91% rubbing alcohol and drying them before first use.
Step 2
Insert a PDR glue stick into the glue gun. Plug in the PDR glue gun and allow it to heat up for 5 minutes.
Step 3
Clean the area to be repaired with 91% isopropyl rubbing alcohol and a clean towel. It is important to remove all wax and grease from the surface to insure the glue and dent pulling tabs properly adhere to the damaged area.
Step 4
Select the correct sized glue pulling dent tab by comparing it to the size of the dent. Larger glue pulling tabs are to be used for larger dents and smaller glue pull tabs used for smaller dents and also for finishing dents.
Step 5
To save time when doing multiple repairs, glue and place all of the glue pull dent tabs at once onto the vehicle; then do all of the repairs one at a time.
Step 6
Apply hot glue to the dent pulling glue tab by pulling on the trigger of the glue gun until approximately a dime-sized amount of glue is released. Use a ‘pea’ sized drop of glue for smaller pulling tabs and a dime size or slightly more for larger tabs.
Step 7
Next, apply the glue pulling tab to the exact center of the dent. Avoid applying too much pressure when placing the dent pulling tab to the dented area, so you do not create too thin of a layer of glue between the car panel and the pulling tab.
Step 8
Allow the glue to set for about 5 minutes prior to using any glue pulling tool. The glue should be hard to the touch at the time you begin repair. If your fingernail leaves an impression in glue, simply allow a couple more minutes for glue to harden. Keep the panel to be repaired out of the direct sunlight so the glue will set properly.
Step 9
Place the paintless dent repair glue pulling tool of choice directly over the dent pulling tab shaft until the female adapter in the center of the dent lifter slides over the shaft of the tab. Adjust the height knob accordingly.
9a. The T-Hand Puller may be used for glue pulling larger dents or to remove the last 10-20% of a dent.
Step 10
If using a dent lifter tool, squeeze the dent lifter handle slowly several times until the desired result is achieved. As the damage gets smaller, reduce the size of the dent-pulling tab until the dent becomes flush. If using a slide hammer or t-puller, repeat usage and keep reducing size of glue pull tab as dents reduce in size.
Step 11
It is common for the dent pulling tab to release from the glue, leaving the glue on the panel of the vehicle. When this occurs, spray 91% rubbing alcohol on the edge of the glue and peel it away using the plastic scraper. You may need to repeat steps #5 to #12 until the desired result is achieved. It is not uncommon to repeat the process up to ten times.
Step 12
Occasionally a high spot is created when pulling the dent. If this were to happen, gently tap down any high spots using the dent hammer and the plastic tap down tool provided, until the dent is flush. Be careful not to tap to hard or you might create additional low spots.
The Ding King Training Institute is a family operated company in business since 1993. We are a State Approved Institution, licensed by the BPPE and are committed to providing each student with an educational experience that includes industry certification. Each of our instructors are experts with combined experience exceeding 100 years and are eager to provide you with the quality training required to become successful. We’ve worked diligently to earn our ranking as The #1 Auto Appearance School in the world, and look forward to demonstrating to you why we’re deserving of your business!
* Training Provider for American Honda Motor Co., Inc.
* PDR Training Provider for Auto Nation.
* OEM Production Line Factory Training for Tesla, Karma, BMW, Volvo & Mercedes Benz.
* I-CAR Sustained Training Partner.
* CTE – Career Technical Educator for High School Students Across the USA.
* Training youthful offenders creating a career pathway with the Department of Corrections.
* NADA, SEMA, NACE and ICA Member for 30 Years.
* A+ Rating with the Better Business Bureau.